4.  Description of its operational parts:

   ①. Power switch

Connect on the power supply; turn on the black boat-shaped switch to lighten the indicator, which shows current blending time.

   ②. Digital Time Controller:

The time controller is used for accurate control of blending time. It’s composed by Display screen、 "Set" button  and "Start" button. Display screen shows setting time; "Set" button at the left panel, for blending time set from 4 ~ 60 seconds, every 2 seconds increase, it can be set freely; "Start" button at the right panel, press it to start working. If halfway suspended, press this button too.

   ③. Mask and forks

      Unfold the mask to loading amalgam capsule; the mask must be closed during working. The fork inside the mask is used to grip amalgam capsule.

5.  Operational procedure:

①. Connect on the power supply; turn on the black boat shaped power switch to lighten the display.

②. Setting times, every short press “SET ” button, the time will increases 2S, every long press “SET” button, the setting time will increases rapidly (The range of time is 4-60 seconds) .Time setting has memory.

③. Fix capsule inside the forks, close the mask (for safety, the machine not working and will have beep sound when the mask was not closed). This system obtained the patent, the Patent No. is: 200520014942.1.

(How to fix amalgam capsule, please find attached operation picture)

④. Press “START” button to start working, while the display shows current blending time, and the setting time will decrease until the machine stop working, there will have a beep sound to remind you blending completed.

⑤. After blending completed, remove capsule from the forks.

⑥. Adjust blending speed between High Speed and Low Speed

 press “SET” and “START” button together, when display screen shows “H” means high speed state; press “SET” and “START” button together again, the display screen will shows “L” ,it means low speed state. After choose your desired speed, please press “SET” button to adjust suitable blending time. (NOTICE: Please choose high speed to blend capsules that from Shanghai or abroad)

6. Attention:

① Before using, remove the transit screw (painted RED on the tip) underside the unit.

② Unpack, inspect all parts if there’s any damage.

③ The machine should be placed on a flat, sturdy and even operating table to avoid any noise that caused by resonance.

④ Do not open the cover of machine optionally to avoid undesired damage.

⑤ For safety, the mask must be closed during operation.

7. Maintain:

① Maintain method: press the buttons properly during operation, if there’s any difference sound or shake, please cut off the power supply immediately, and ask for maintain. Make sure the cases and forks are clean after using. It can be cleaned with antibacterial surface cleaners.

② Maintenance period: generally after one year using, the machine should maintenance, especially check the strength of the forks. If amalgam capsule becomes loose or forks were damaged, please replace the matching spare parts immediately.

③ Method of replace fuse: it should fix F2AФ5×20 fuse, unscrew the fuse socket down with “Crossing screwdriver”, fix F2AФ5×20 fuse into and tighten the cap with clockwise.

8. Common Fault Exclusion:

⑴ The machine parts are not working: Check if the fuse were broken down, replace the fuse tube.

⑵ Timer system or other faults: Send to professional department or manufacturer to maintain.

⑶ The mask damages: When connect to the power supply, press “Start/Stop” button, the machine not working, maybe the hall element, which in the mask were dropped. Following is the solution:

Processing methods:

① turn off power switch, press down the “Start/Stop” button, while turn on the power switch, the display shows “O” or “U”, then release the “Start/Stop” button. ② after that press “Set” button, the display will show “U” or “O” 【if first step ①, the display shows “O”, then the second step ②, the display will show “U”, Vice versa.】turn off the power switch after setting as above. ③ Turn on the power switch again, in the state of “O”, open the mask, the machine will stop working; in the state of “U”, open the mask, the machine will continue working.

9. Part list:

①. Main frame              1set

②.Warranty Card           1piece

③. Spring                  2pcs

④. Fuse                   2pcs

⑤. Forks                  1pair

⑥.Manual                 1piece

⑦.Quality Certificate        1piece